iPad Mini 6电池更换维修教程

自己修 阅读:276 2024-03-28 16:14:28 评论:0
iPad Mini 6 Battery Replacement, Apply tape to a cracked screen: 步骤 1 中的图像 1,3 iPad Mini 6 Battery Replacement, Apply tape to a cracked screen: 步骤 1 中的图像 2,3 iPad Mini 6 Battery Replacement, Apply tape to a cracked screen: 步骤 1 中的图像 3,3

    如果您的屏幕破裂,请控制进一步的破裂,并在维修过程中用胶带封住玻璃,防止对身体造成伤害。

    将透明包装带重叠放置在iPad显示屏上,直到整个表面都被覆盖。

    这将保持玻璃碎片的控制,并在撬起显示器时提供结构完整性。

    请尽最大努力按照说明遵循指南的其余部分。然而,一旦玻璃破碎,它很可能会在你工作时继续破裂,你可能需要使用金属撬具将玻璃铲出。

    佩戴安全眼镜保护眼睛,注意不要损坏液晶显示屏。

注意:步骤 2-13 源自标记为进行中的 指南

iPad Mini 6 Battery Replacement, Heat the bottom edge: 步骤 2 中的图像 1,1

    在开始之前完全关闭设备电源。

    将加热的开屏器紧贴在设备的底部边缘90秒,以松开下面的粘合剂。

    也可以使用吹风机、热风枪或热板,但要小心不要使设备过热。

iPad Mini 6 Battery Replacement, Screen removal information: 步骤 3 中的图像 1,3 iPad Mini 6 Battery Replacement, Screen removal information: 步骤 3 中的图像 2,3 iPad Mini 6 Battery Replacement, Screen removal information: 步骤 3 中的图像 3,3

    在等待粘合剂松开时,请注意以下事项:

    屏幕顶部和底部的区域对撬开很敏感。

    插入的厚度不要超过3毫米,以免损坏屏幕。

    屏幕上有一块长电路板,与左边缘平行。

    插入的厚度不要超过1.5毫米,以免损坏电路板。

    前两个图像被镜像用于演示目的。

iPad Mini 6 Battery Replacement, Insert an opening pick: 步骤 4 中的图像 1,3 iPad Mini 6 Battery Replacement, Insert an opening pick: 步骤 4 中的图像 2,3 iPad Mini 6 Battery Replacement, Insert an opening pick: 步骤 4 中的图像 3,3

    一旦屏幕摸起来很热,就在屏幕的底部边缘并尽可能靠近边缘处使用吸力手柄。

    用抽吸手柄提起要拆的组件,在要拆的组件和机壳之间形成一个小间隙。

    在框架和屏幕之间的间隙中插入拆机片。

    插入工具时不要超过1.5毫米,以免损坏电路板。

    将开口工具留在原位,以防止粘合剂重新密封。

iPad Mini 6 Battery Replacement, Separate the bottom adhesive: 步骤 5 中的图像 1,3 iPad Mini 6 Battery Replacement, Separate the bottom adhesive: 步骤 5 中的图像 2,3 iPad Mini 6 Battery Replacement, Separate the bottom adhesive: 步骤 5 中的图像 3,3

    沿着设备的底部边缘向右下角滑动工具。

    将工具留在原位,以防止粘合剂重新密封。

iPad Mini 6 Battery Replacement, Heat the right edge: 步骤 6 中的图像 1,1

    将加热的开屏器紧贴在设备的右边缘90秒,以松开下面的粘合剂。

iPad Mini 6 Battery Replacement, Separate the bottom-right corner adhesive: 步骤 7 中的图像 1,3 iPad Mini 6 Battery Replacement, Separate the bottom-right corner adhesive: 步骤 7 中的图像 2,3 iPad Mini 6 Battery Replacement, Separate the bottom-right corner adhesive: 步骤 7 中的图像 3,3

    围绕设备的右下角旋转拆机片。

iPad Mini 6 Battery Replacement, Separate the remaining adhesive: 步骤 8 中的图像 1,2 iPad Mini 6 Battery Replacement, Separate the remaining adhesive: 步骤 8 中的图像 2,2

    重复加热、切片,并为设备的剩余边缘保留拆机片。

    当你在前置摄像头附近切片时,插入的拆机片不要超过1.5毫米,以免损坏或弄脏摄像头。

iPad Mini 6 Battery Replacement, Reposition the screen: 步骤 9 中的图像 1,3 iPad Mini 6 Battery Replacement, Reposition the screen: 步骤 9 中的图像 2,3 iPad Mini 6 Battery Replacement, Reposition the screen: 步骤 9 中的图像 3,3

    如果屏幕边缘仍有阻力,请使用拆机片再次切割粘合剂。

    不要一直试图移除屏幕;它仍然通过柔性电缆连接到框架。

    使设备的底部面向您,向上拉屏幕的右边缘,使其朝向设备的左边缘。

    继续操作前,将屏幕倒置并与框架平行放置。

    不要扭曲屏幕或将屏幕移离框架太远,以免损坏柔性电缆。

iPad Mini 6 Battery Replacement, Unfasten the display cable bracket: 步骤 10 中的图像 1,2 iPad Mini 6 Battery Replacement, Unfasten the display cable bracket: 步骤 10 中的图像 2,2

    使用#000螺丝刀拆下将机壳支架固定至机壳的五个1.2 mm长的螺丝。

iPad Mini 6 Battery Replacement, Remove the display cable bracket: 步骤 11 中的图像 1,2 iPad Mini 6 Battery Replacement, Remove the display cable bracket: 步骤 11 中的图像 2,2

    使用镊子或手指将显示屏电缆支架从机壳上取下。

iPad Mini 6 Battery Replacement, Disconnect the display: 步骤 12 中的图像 1,3 iPad Mini 6 Battery Replacement, Disconnect the display: 步骤 12 中的图像 2,3 iPad Mini 6 Battery Replacement, Disconnect the display: 步骤 12 中的图像 3,3

    使用撬棒的平端向上撬起并断开固定在机壳上的显示屏电缆的两个压接头。

iPad Mini 6 Battery Replacement, Remove the screen: 步骤 13 中的图像 1,2 iPad Mini 6 Battery Replacement, Remove the screen: 步骤 13 中的图像 2,2

    从机壳上拆下要拆的组件。

iPad Mini 6 Battery Replacement, Disconnect the battery: 步骤 14 中的图像 1,2 iPad Mini 6 Battery Replacement, Disconnect the battery: 步骤 14 中的图像 2,2

    用撬棒的平端撬起并断开固定在框架上的电池压接器。

    要像这样重新连接压接头,请小心对齐并向下按压一侧,直到其卡入到位,然后在另一侧重复此操作。不要在中间往下压。如果接头错位,引脚可能会弯曲,造成永久性损坏。

iPad Mini 6 Battery Replacement, Battery removal information: 步骤 15 中的图像 1,2 iPad Mini 6 Battery Replacement, Battery removal information: 步骤 15 中的图像 2,2

    在开始该过程之前,请注意以下事项:

    必须拆下四个可伸缩粘合胶拉片才能分离电池下方的粘合胶。

    粘合剂的剩余部分位于电池的顶部边缘,靠近连接器;插入塑料卡时请记住这一点。

iPad Mini 6 Battery Replacement, Remove the stretch release adhesive: 步骤 16 中的图像 1,2 iPad Mini 6 Battery Replacement, Remove the stretch release adhesive: 步骤 16 中的图像 2,2

    用镊子或手指抓住其中一条胶带上的黑色拉片。

    注意不要用工具刺穿或弯曲电池——刺穿或弯曲的电池可能会泄漏危险化学品或引发火灾。

iPad Mini 6 Battery Replacement: 步骤 17 中的图像 1,3 iPad Mini 6 Battery Replacement: 步骤 17 中的图像 2,3 iPad Mini 6 Battery Replacement: 步骤 17 中的图像 3,3

    以小角度缓慢而稳定地拉出饰条。给它足够的时间从电池下面伸展和松开。

    如果胶带断了,试着用手指或钝镊子将其取出,然后继续拉——但不要撬电池下面。

    对所有四条可伸缩胶带重复此过程。

iPad Mini 6 Battery Replacement, Apply isopropyl alcohdiv: 步骤 18 中的图像 1,1

    注意不要用工具刺穿或弯曲电池——刺穿或弯曲的电池可能会泄漏危险化学品或引发火灾。如果你很难拔出电池,请多涂一些异丙醇,然后再试一次。

    在电池顶部边缘周围的缝隙中滴几滴高浓度(超过90%)异丙醇。

iPad Mini 6 Battery Replacement: 步骤 19 中的图像 1,2 iPad Mini 6 Battery Replacement: 步骤 19 中的图像 2,2

    向上倾斜设备的顶部边缘,使异丙醇在电池下方流动。

    保持1-2分钟,让异丙醇有时间使粘合剂变弱。

iPad Mini 6 Battery Replacement, Separate the battery's adhesive: 步骤 20 中的图像 1,3 iPad Mini 6 Battery Replacement, Separate the battery's adhesive: 步骤 20 中的图像 2,3 iPad Mini 6 Battery Replacement, Separate the battery's adhesive: 步骤 20 中的图像 3,3

    将塑料卡插入电池顶部边缘和框架之间的间隙。

    用塑料卡将电池下面的粘合剂切成薄片。

iPad Mini 6 Battery Replacement, Remove the battery: 步骤 21 中的图像 1,3 iPad Mini 6 Battery Replacement, Remove the battery: 步骤 21 中的图像 2,3 iPad Mini 6 Battery Replacement, Remove the battery: 步骤 21 中的图像 3,3

    用塑料卡撬起,将电池与机壳分离。

    拆下电池。

    如果还有酒精残留,在安装新电池之前,请用无纺布将其擦掉或晾干。

    在重新装配过程中,清除旧的粘合胶,然后使用拉伸释放胶带、双面胶带或预切粘合胶固定新电池。

    拆下电池后,请勿重复使用,因为这样做会有潜在的安全隐患。

标签:iPad mini 6